VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Cartridge  /  Vape Cartridge heating and temperature — a primer
vape cartridges · adult smokers

Vape Cartridge heating and temperature — a primer

Vape Cartridge is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Published 10 September 2025  ·  VapeWholesaleHub  ·  Reading time 8 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.

How the price is actually built

Ordering vape cartridge is not difficult. Ordering vape cartridge that sell through without a return queue behind them is the part most buyers underestimate, and it is where we spend our time. We supply adult smokers in European and North American markets with core lines that turn over predictably, and we keep the specification list short enough for your team to actually manage.

We publish a realistic band of 1.89 to 5.96 per unit for standard configurations at 300 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

Batch consistency and why it matters

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

For adult smokers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What happens when something goes wrong

We keep the specification sheet for every order on file. Two years later, when a customer asks whether a pod is compatible, the answer is a lookup rather than a guess.

For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.

  • Document pack prepared per destination market
  • Consolidated or split shipping, quoted both ways
  • Reference sample retained from every batch
  • Seven-day defect reporting with replace-or-credit
  • Standing reorder schedule with a fixed cut-off
  • Specification locked in writing before production starts

Labels, closures and traceability

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

Artwork approval is a two stage process: a digital proof for text and layout, then a physical dummy for colour and finish. Skipping the dummy is the single most common cause of a reprint.

Specification summary

Typical specification for this category
Volume1.0 ml
CoreMesh
Resistance1.8 ohm
Thread510 thread
AirflowSide
PackagingBlister
Minimum order200 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

What is the minimum order for vape cartridge?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Related reading

Need a quotation on vape cartridges?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape cartridges

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us